Antec Nine Hundred Two V3 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Caixas de computador Antec Nine Hundred Two V3. Antec Nine Hundred Two V3 Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
  • Página
    / 15
  • Índice
  • MARCADORES
  • Avaliado. / 5. Com base em avaliações de clientes
Vista de página 0
NINE HUNDRED TWO V3
U
SER
S
M
ANUAL
Vista de página 0
1 2 3 4 5 6 ... 14 15

Resumo do Conteúdo

Página 1 - NINE HUNDRED TWO V3

NINE HUNDRED TWO V3 USER’S MANUAL

Página 2 - Table of Contents

9 Pin Signal Names (HDA) Pin Signal Names (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 6 MIC2_JD 6

Página 3

10 3.5 Rewiring Motherboard Header Connections There may come a time that you need to reconfigure the pin-out of a motherboard header connector. E

Página 4 - 1.2 Diagram

11 Size: 200 x 30 mm three-speed fan Rated Voltage: 12V DC Operating Voltage: 10.8V ~ 13.2V Speed (RPM) Input Current Air Flow Static Pressure

Página 5 - Hardware Installation Guide

12 Size: 120 x 25 mm TriCool™ fan Rated Voltage: 12V Operating Voltage: 10.2V - 13.8V Speed (RPM) Input Current Air Flow Static Pressure Acousti

Página 6

13 the holes in the fan are secured to the mount. 3. Use the long screws provided to secure the fan to the mount. Do not overtighten. 4. Run the p

Página 7

14 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rot

Página 8

1 Table of Contents Introduction 1.1 Case Specifications ...

Página 9

2 Congratulations on your purchase of the Nine Hundred Two V3! The best-selling Antec Nine Hundred offers gamers an unbeatable enclosure, one that

Página 10

3 1.1 Case Specifications Case Type Mid Tower Color Black Dimensions 19.3” (H) x 8.7” (W) x 18.5” (D) 493 mm (H) x 218 mm (W) x 472 mm (D) Weight 2

Página 11 - Cooling System

4 Hardware Installation Guide 2.1 Setting Up 1. Place the case upright on a flat, stable surface so that the rear panel (power supply and expansi

Página 12

5 4. Lift up and remove the motherboard. 5. Screw in the brass standoffs to the threaded holes that line up with the motherboard. 6. Place the

Página 13

6 7. There is a 120 mm fan pre-installed into each cage. Connect the 4-pin connector to the power supply. Note: There is a middle fan bracket p

Página 14

7 2.8 Internal 2.5” Device Installation At the bottom of your case, there are mounting holes designed to support one 2.5” SSD device. 1. Loca

Página 15

8 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Gro

Comentários a estes Manuais

Sem comentários