Antec DF-30 Manual do Utilizador

D F-30 DARK FLEET THE ADVANCED GAMING FORCE US E R MA N U A L

10 2.1 SETTING UP Put the case upright on a flat, stable surface so that the rear panel (power supply and expansion slots) is facing you. To remove

11 Now rest your case with the left side up. Here’s what we’ll be working with first: A – Power supply mounts B – 5.25” drive bay area C – 3.5” dr

12 2.2 MOTHERBOARD INSTALLATION Before proceeding: - Check the manual for your CPU cooler to find out if there are steps you must do befor

13 3. Now remove your motherboard by lifting it up. Lift your motherboard out to install the standoffs. 4. Install standoffs as needed and put th

14 Note: The DF-30 comes with a CPU cutout on the motherboard tray, which will allow you to change your CPU heatsink without removing the motherboar

15 Use these screws to secure your power supply to the case. 2.4 CABLE MANAGEMENT There is a cable management compartment behind the 3

16 2.5 INTERNAL 3.5” DEVICE INSTALLATION The DF-30 includes two Fleet-Release™ access doors. With the front bezel facing you, they are l

17 Installing a 3.5” internal device 3. Fasten the device in place with the provided screws on both side of the drive cage. Make sure to install s

18 2.6 EXTERNAL 3.5” DEVICE INSTALLATION There is one external 3.5” drive bay under the 5.25” drive bays. Remove this drive bay cover. 1. Caref

19 2.7 USING THE TOP 2.5” HOT-SWAP BAY The DF-30’s top 2.5” hard drive bay is hot-swap capable. To use the hot-swap feature, ensure that y

2 DF-30 USER’S MANUAL Congratulations on your purchase of the Antec Dark Fleet DF-30. Meet the swifter, lighter Dark Fleet enclosure with the heavyw

20 2.8 EXTERNAL 5.25” DEVICE INSTALLATION There are three externally accessible 5.25” drive bays. Before you begin, remove both side pa

21 2.9 INTERNAL 2. 5” DEVICE INSTALLATION There is a 2.5” device mounting location located at the bottom of the case. To use this mount

22 3. FRONT I/O PORTS SECTION 3

23 Pin Signal Names Pin Signal Names 1 USB Power 1 2 USB Power 2 3 Negative Signal 1 4 Negative Signal 2 5 Positive Signal 1 6 Positive Signal 2 7 Gro

24 3.3 POWER SWITCH / RESET SWITCH / HARD DISK DRIVE LED CONNECTORS Connected to your front panel are LED and switch leads for power, re

25 COOLING SYSTEM SECTION 4

26 4.1 INCLUDED FANS Standard fans on the DF-30: A – 1 x 120 mm rear TwoCool™ LED fan B – 1 x 140 mm top TwoCool™ fan C – 2 x Fleet-Re

27 4.2 TOP 140 MM TWOCOOL™ FAN The DF-30 comes with one 140mm TwoCool™ LED fan. This fan has a two-speed switch that lets you choose the

28 4.4 REAR EXHAUST 120 MM TWOCOOL™ FANS There is one 120 x 25 mm TwoCool™ blue LED fan preinstalled at the rear of the case. This fan is

29 4.6 WASHABLE AIR FILTERS There is a filter located behind the faceplate of each Fleet-ReleaseTM Access Doors. There are total of th

3 TABLE OF CONTENTS SECTION 1: INTRODUCTION 1.1 Getting to know your case…………………………………………………. 5 1.2 Case specifications………………………………………………………….

30 Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 tel: 510-770-1200 fax: 510-770-1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterda

4 INTRODUCTION SECTION 1

5 1.1 GETTING TO KNOW YOUR CASE Drive bays Hardware mounts 1 5.25” drive bays 8 Motherboard stando

6 1.2 CASE SPECIFICATIONS CASE TYPE Mid Tower COLOR Matte black DIMENSIONS 19.1″ (H) x 7.8″ (W) x 19.1″ (D) 485 mm (H) x 198 mm (W) x

7 1.3 BEFORE YOU BEGIN In order to ensure that your building experience with the Dark Fleet DF-30 will be a positive one, please take no

8 1.4 LOCATING AND POSITIONING YOUR COMPUTER Your DF-30 has backwards- and top-facing exhaust fans, as well as front-mounted intake fans

9 HARDWARE INSTALLATION SECTION 2